EUTECH INSTRUMENTS CYBERSCAN DO 1500 DO METER Manuál s instrukcemi

Instruction Manual CyberScan DO 1500 Dissolved Oxygen Meter 68X292336 Rev. 1 01/04 TechnologyMad

Instruction Manual CyberScan DO 1500 7 P 1.0: View calibration data- View the last calibrated cal factor and 0% offs

Instruction Manual CyberScan DO 1500 8 4.1.1. Setup P 1.0: View the Calibration Data This setup menu allows you to view

Instruction Manual CyberScan DO 1500 9 2. Press enter to access View Last calibrated Cal factor setup page.  press to

Instruction Manual CyberScan DO 1500 10 3. If the unit has not been standardised, a series of dashes will appear on the

Instruction Manual CyberScan DO 1500 11 4.1.2. Setup P 2.0: Set Pressure The setup option allows you to set the atmo

Instruction Manual CyberScan DO 1500 12 3. Press enter to go to the ‘Pressure adjustment’ setup page as shown below. 4

Instruction Manual CyberScan DO 1500 13 4.1.3. Setup P3.0: Set the Salinity Value The setup option allows you to set th

Instruction Manual CyberScan DO 1500 14 3. Press enter to go to the ‘Salinity adjustment’ setup page as shown below. 4

Instruction Manual CyberScan DO 1500 15 4.1.4. Setup P4.0: Select Number of User Cal Points for %Sat calibration

Instruction Manual CyberScan DO 1500 16 3. Press enter to accept the current value or press  or  to adjust and set

PREFACE Thank you for selecting the Eutech Instruments CyberScan DO 1500 bench meter. The instruction manual serves to explain the use of the Cybe

Instruction Manual CyberScan DO 1500 17 4.1.5. Setup P5.0: Enable/ Disable Auto Cal This setup option allows you to e

Instruction Manual CyberScan DO 1500 18 3. Press  or  to select YES or NO. 4. Press enter key to confirm selection a

Instruction Manual CyberScan DO 1500 19 4.1.6. Setup P6.0: Select the Temperature Unit sel ect  press to set valu

Instruction Manual CyberScan DO 1500 20 3. Press  or  key to select °C or °F. 4. Press enter key to confirm selectio

Instruction Manual CyberScan DO 1500 21 4.1.7. Setup P7.0: Enable/ Disable Stability Indicator This setup option allow

Instruction Manual CyberScan DO 1500 22 3. Press  or  key to select ON or OFF. 4. Press enter key to confirm selecti

Instruction Manual CyberScan DO 1500 23 4.1.8. Setup P8.0: Baud Rate This setup option allows you to set the baud rate

Instruction Manual CyberScan DO 1500 24 3. Press  or  key to toggle between 4800, 9600, 19200 or 38400. 4. Press

Instruction Manual CyberScan DO 1500 25 4.1.9. Setup P9.0: Parity Bit This setup option allows you to set the parity bi

Instruction Manual CyberScan DO 1500 26 3. Press  or  key to toggle between toggle between 0 (none), 1 (odd) or 2 (eve

TABLE OF CONTENTS 1. INTRODUCTION 1 2. GETTING STARTED 2 2.1. Connectors 2 3. USING THE METER 3 3.1. The Electrode 3 3.2. Display/ Keys

Instruction Manual CyberScan DO 1500 27 4.1.10. Setup P10.0: Stop Bit This setup option allows you to set the stop bit

Instruction Manual CyberScan DO 1500 28 3. Press  or  key to toggle between 1 or 2. 4. Press enter key to confirm se

Instruction Manual CyberScan DO 1500 29 4.1.11. Setup P11.0: Print Data This setup option allows you to print current d

Instruction Manual CyberScan DO 1500 30 3. Press  or  key to toggle between Curr or Store. 4. Press enter key to con

Instruction Manual CyberScan DO 1500 31 4.1.12. P12.0: Clear Stored Data This setup option allows you to clear all stor

Instruction Manual CyberScan DO 1500 32 3. Press  or  key to toggle between YES or NO. 4. Press enter key to confirm

Instruction Manual CyberScan DO 1500 33 4.1.13. P13.0: Clear Buffer Values This setup option allows you to clear the st

Instruction Manual CyberScan DO 1500 34 3. Press  or  key to toggle between YES or NO. 4. Press enter key to confirm

Instruction Manual CyberScan DO 1500 35 5. USER CALIBRATION 5.1. %Sat – One Point calibration (Auto) User can do the

Instruction Manual CyberScan DO 1500 36 5.2. %Sat – Two Point calibration (Auto) User must do the 0.0%Sat cal first. T

Instruction Manual CyberScan DO1500 11. INTRODUCTION Thank you for selecting a Eutech Instruments CyberScan Dissolved Ox

Instruction Manual CyberScan DO 1500 37 5.3. %Sat – One Point calibration (Manual) User can calibrate to the know valu

Instruction Manual CyberScan DO 1500 38 5.4. mg/L– One Point calibration (Auto) User can do calibration in mg/L. 1.

Instruction Manual CyberScan DO 1500 39 5.5. mg/L– One Point calibration (Manual) User can do calibration in mg/L. 1

Instruction Manual CyberScan DO 1500 40 5.6. ATC Calibration User can adjust the ATC temperature offset. 1. From th

Instruction Manual CyberScan DO 1500 41 saveprintentersaveview6. MEMORY 6.1. Store Value into Memory In any measur

Instruction Manual CyberScan DO 1500 42 stdprintenter7. PRINT DATA 7.1. Printing Data Depending on the print option i

Instruction Manual CyberScan DO 1500 43 8. DO THEORY The polarographic type Oxygen probe used with the CyberScan DO 1500

Instruction Manual CyberScan DO 1500 44 9. METER SPECIFICATIONS Description CyberScan DO 1500 DO range 0.00 to 60.

Instruction Manual CyberScan DO 1500 45 10. CLEANING This meter requires no regular maintenance, but it is recommended t

Instruction Manual CyberScan DO 1500 46 12. ACCESSORIES Consult your Authorised Distributors for these items. 12.1.

Instruction Manual CyberScan DO 1500 2 2. GETTING STARTED 2.1. Connectors 1. Review the layout and arrangement of th

Instruction Manual CyberScan DO 1500 47 13. WARRANTY Eutech Instruments supplies this bench meter with a 3-year warranty

Instruction Manual CyberScan DO 1500 48 14. NOTICE OF COMPLIANCE Warning This meter generates, uses, and can radiate r

For more information on Eutech Instruments products, contact your nearest Eutech Instruments distributor or visit

Instruction Manual CyberScan DO 1500 3 3. USING THE METER 3.1. The Electrode This meter comes equipped with a self

Instruction Manual CyberScan DO 1500 4  press to select optionssetup to standardizepress to store/recall datapres

Instruction Manual CyberScan DO 1500 5 3.3. Screen Display Familiarise yourself with the layout of the digital screen d

Instruction Manual CyberScan DO 1500 6 stdprintentersaveview4. SETUP PROCEDURE CHECK 4.1. CyberScan DO 1500 Setup Pa